* These are Tibbo BASIC/C-programmable devices and their function depends on the loaded app.
We offer many ready-to-use apps, among them a serial-over-IP (SoI) app and Modbus Gateway app.

RS485 Modbus Sensors (Bus Probes)

Bus Probes are a family of environmental sensors with an RS485 interface. The probes communicate using the standard Modbus RTU protocol.

At the moment, Tibbo offers four types of probes: an ambient temperature sensor (BP#01), an ambient temperature and humidity sensor (BP#02), an ambient light sensor (BP#03), and a three-axis accelerometer (BP#04).

Bus Probes are typically wired to a twisted pair cable that distributes power and carries RS485 "+" and "-" lines. All probes accept a supply voltage from 4V to 15V, allowing you to power them with 5V sources (for example, the 5V output of Tibbit #00-3) or standard 12V power supplies. The wide supply voltage range also means that you can allow for a significant voltage drop along the bus (e.g., when using a bus cable of considerable length).

Bus Probes are very compact (measuring only 40x36mm externally) and sport an attractive look and feel. Each sensor has two mounting holes for attaching it to walls and other surfaces.

Bus Probes can be configured and tested using our web-based test app (you will need to connect the probes to your PC via our Web485 board). Tibbo also offers a browser-based test kit (see BP-TEST-WEB-KIT below), which consists of four Bus Probes (one of each type), a Web485 board, and the necessary cables.

Two Tibbo Project System (TPS), Gen. 2-compatible Tibbo BASIC applications for the setup and testing of Bus Probes are available: BP-Tester-UI and BP-Tester-Web. We also offer a TPS-based test kit (see BP-TEST-KIT below), which consists of four Bus Probes (one of each type), a TPS2L(G2) preloaded with the BP-Tester-UI app, and the necessary cables.

Here is How You Can Use Bus Probes

Use the probes in your
Modbus system

Tibbo Bus Probes feature an RS-485 interface and support the industry-standard Modbus RTU protocol. Therefore, existing Modbus systems can use them as general-purpose environmental sensors.

Note: To aid in the creation of sophisticated Modbus systems and network-enablement of serial Modbus devices, Tibbo offers Modbus Gateways.

Deploy the probes as a part of our
TPS-based Remote I/O solution

Our Remote I/O solution supports the use of Bus Probes. Connect the probes to the RS-485 port on a standard TPS-based controller and collect environmental data via the RS-485 bus.

Combine TPS devices with Bus Probes to create environmental monitoring systems.

Key Features

Half-duplex RS-485
interface
Modbus RTU
protocol
4V to 15V power

Available Probes

BP#01: Ambient temperature
sensor
BP#02: Ambient temperature
and humidity sensor
BP#03: Ambient
light sensor
BP#04: Three-axis
accelerometer

Hardware

Specifications:

  • Half-duplex (two-wire) RS-485 interface
  • Communications parameters: 38400-8-N-1
  • Modbus RTU protocol
  • BP#01 (ambient temperature sensor)
    • Measurement range: -40°C to 125°C1
    • Measurement resolution: 0.25°C
    • Measurement accuracy: ±1°C2
  • BP#02 (ambient temperature and humidity sensor)
    • Temperature measurement
      • Measurement range: -25°C to 50°C
      • Measurement resolution: 0.5°C
      • Measurement accuracy: not specified3
    • Humidity measurement:
      • Measurement range: 10 to 90% RH
      • Measurement resolution: ±0.1% RH
      • Measurement accuracy: ±5% RH4
      • Temp. range for valid humidity measurements: 5°C to 50°C
  • BP#03 (ambient light sensor)
    • Measurement range: 1 to 65528 lux
    • Measurement resolution: 1 lux
    • Measurement accuracy: 1 lux
  • BP#04 (three-axis accelerometer)
    • Independent X, Y, and Z axes
    • Measurement range for each axis: ±6G
    • Measurement resolution for each axis: 0.003G
    • Measurement accuracy for each axis: 0.1G
  • Green and red status LEDs
  • Power: 4V to 15V DC
  • Dimensions, excluding connectors (L x W x H): 40 x 36 x 19mm
  • Operating temperature range: -40°C to +85°C
  • Internal firmware is upgradeable through the RS-485 port
  • CE and FCC-certified
  1. The actual measurement range is limited by the operating temperature range of the Bus Probe itself, which is from -40°C to +85°C.
  2. Independent lab tests commissioned by our Romanian distributor found BP#01's measurement accuracy for ambient temperature to be ±0.45°C or better.
  3. Independent lab tests commissioned by our Romanian distributor found BP#02's measurement accuracy for ambient temperature to be ±0.5°C or better.
  4. Independent lab tests commissioned by our Romanian distributor found BP#02's measurement accuracy for relative humidity to be ±3.8% or better.

See Also:

Apps, Files, and Documentation

Test ApplicationsBus Probe Web-based Tester App
Bus Probe Web-based Firmware Updater App
TPS-based Test App (UI version)
TPS-based Test App (web interface version)
Probe Firmwarebp_application_firmware_v.bin
DocumentationBus Probe Manual
CE Certificatebp01_02_03_04-ce.pdf
FCC Certificatebp01_02_03_04-fcc.pdf

Order BPx Bus Probes

Browser-based test kit for Bus Probes #01, #02, #03, and #04

Browser-based test kit for Bus Probes #01, #02, #03, and #04

This Kit is intended for use with our RS485 Modbus Sensor Test App.

TPS-based test kit for Bus Probes #01, #02, #03, and #04

TPS-based test kit for Bus Probes #01, #02, #03, and #04

BP#01: Ambient Temperature Sensor

BP#01: Ambient Temperature Sensor

BP#02: Ambient Temperature and Humidity Sensor

BP#02: Ambient Temperature and Humidity Sensor

BP#03: Ambient Light Sensor

BP#03: Ambient Light Sensor

BP#04: 3-axis Accelerometer

BP#04: 3-axis Accelerometer